Black & Decker EGBL14 Instruction Manual download pdf (Page 6)

ENGLISH

(Original instructions)

Assembly

Warning! Before assembly, remove the battery from the tool.

Fitting and removing the battery (g. B)

u To t the battery (5), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (9) while at

the same time pulling the battery out of the receptacle.

Fitting and removing a drill bit or screwdriver bit

(g. C)

This tool is tted with a keyless chuck to allow for an easy

exchange of bits.

u Grasp the rear half of the chuck (3) with one hand and use

your other hand to rotate the front half in the

counterclockwise direction, as viewed from the chuck end.

u Insert the bit shaft (10) into the chuck.

u Firmly tighten the chuck by holding the rear half of the

chuck and rotating the front portion in the clockwise

direction as viewed from the chuck end.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

u To charge the battery (5), insert it into the charger (7). The

battery will only t into the charger in one way. Do not

force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (8) will blink.

The charge is complete when the charging indicator (8)

switches to continuously on. The charger and the battery can

be left connected indenitely. The LED will switch on as the

charger occasionally tops up the battery charge.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Selecting the direction of rotation (g. D)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the torque

This tool is tted with a collar to set the torque for various

screwdriving and drilling applications. Large screws and hard

workpiece materials require a higher torque setting than small

screws and soft workpiece materials. For the denition of the

symbol refer to the listing below.

u For drilling in wood, metal and plastics, set the torque

adjustment collar (4) to the

symbol.

u For screwdriving, set the collar to the desired setting. If

you do not yet know the appropriate setting, proceed as

follows:

- Set the torque adjustment collar (4) to the lowest torque

setting.

- Tighten the rst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/

reverse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the drill

bit.

u Just before the drill tip breaks through the other side of the

workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

u Use spade bits when drilling large diameter holes in wood.

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Black & Decker EGBL14 Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for Cordless screwdrivers Black & Decker EGBL14