Black-decker 3004 User Manual download pdf

SAFETY PRECAUTIONS WITH SAWS

1. Disconnect plug from power supply

before changing blades, making

cutting depth or cutting angle ad

justments, lubricating, inspecting,

or when saw is not being used.

2. When retracting thè lower blade

guard, always use the retracting

knob on the guard.

3. Never tie back the lower blade

guard or its retracting knob.

4. When sawing never reach under

neath the material for any reason.

5. Always be sure that the saw will

be properly grounded before plug

ging into power supply. See fol

lowing section.

6. Keep blade sharp..Dull blades may

cause the saw to swerve or stall

under pressure.

7. Wear safety goggles when the cut

ting of material results in flying

particles. If material forms dust

when cut, also use a dust mask.

8. If you drop or damage the saw,

unplug it first; then check to see

if the blade and lower blade guard

operate freely before resuming

operations.

9. If saw stalls, release the trigger

and disconnect plug from power

supply before attempting to loosen

the unit.

GROUNDED

OUTLET

BOX

--------

Fig. A

GROUNDING

BLADE IS THE

LONGEST OF

THE 3 BLADES

GREEN

GROUNDING

EVERY ELECTRIC TOOL SHOULD BE GROUNDED while in

use to protect the operator against shock. This unit is

equipped with approved 3-conductor cord and 3-blade

grounding type attachment plug to be used with the proper

grounding type receptacle. The green colored conductor In

the cord is the grounding wire. Never connect the green wire

to a “live" terminal.

If your unit requires less than 150 volts, it has a plug that

looks like fig. “A". A special grounding adapter (Fig. “B") is

available from your dealer to permit using 2-wire receptacle

until the correct receptacle is properly installed. The green

grounding wire extending from the side of the adapter must

be connected to a PERMANENT GROUND such as a properly

grounded outlet box.

If you use an extension cord, be sure that it is a 3-conductor,

grounding-type cord. Grounding must be continuous from the

tool plug to a grounded receptacle.

When using the tool at a considerable

distance from power source, a 3-wire

grounding-type extension cable of ade

quate size must be used for safety and to

prevent loss of power and over-heating.

Use the table at right for 120-volt tools.

For 220-volt tools, use wire size corre

sponding to an extension length of I/2

the contemplated length.

P.T.I. Safety Rule #12 applies to Exten

sion Cords as well as the Tool Power

Cord. Before using cords, inspect them

for loose or exposed wires and damaged

insulation. Make any needed repairs or re

placement before using your power tool.

Ext. cable

length

in feet . . 25 50 75 100

Required

wire size

(A.W.G.)

in cable.. 16 14 12 10

BRUSHES

Carbon motor brushes should be inspected

frequently for wear. To inspect brushes,

FIRST, UNPLUG SAW FROM POWER

SUPPLY. Then, with a screwdriver, slide

the brush cover plates outward and the

brush spring will pop out. Put the spring,

with attached wire extended out of the

opening into the position shown at right

and tilt the saw so that the carbon brush

will drop out of the opening. If the brush

is worn down to the grooved line on its

side, a new brush is needed and can be

obtained from any of the locations shown

on the next page.

OWNER’S MANUAL

To reassemble, insert brush with worn

end toward motor, or a' new brush with

longest distance from end to grooved line

toward motor. Next, insert the small brass

plate behind the brush, and then feed in

the spring until the round spring cap fits flush with the opening. This allows

the cover plate to be pushed back Into the closed position.

KNOB FOR

iETRACTlNG

LOWER BLADE

GUARD

TRIGGER SWITCH:

PULL-“0N"; RELEASE-"OFF’'

IIP FENCE

Quickly attaches for fast,

smooth rip cuts without pen

ciled guide lines. U-1914

49531 SAW PROTRACTOR

Permits accurate cuts, 0° to

90° angles. Saves time and

effort.

55582 CUT-OFF GUIDE

One-piece die-cast aluminum

guide for making accurate

cuts.

GUIDE LINE

FOR

VERTICAL CUTS

SLIDING

BRUSH COVER

PLATE

CUTTING I

ADJUSTMENT

CUTTING DEPTH: At 90° - i/s" to 2%'\ At 45° bevel - 0" to !%"•

BEVEL ADJUSTMENT: 0° to 45°.

120 VOLTS A.C. ONLY 9.5 AMPS I1/2 H.P. 4700 R.

.P.M.

THE BLACK & DECKER MFG. CO., TOWSON, MD. 21204, U.S.A.

7'A” CIRGUUR SAW

model 3004

Form No. 97243 AL

Printed in U.S.A.

1 2

OWNER’S MANUAL 1
&. Decker 2

Summary of Contents

Page 1 - OWNER’S MANUAL

SAFETY PRECAUTIONS WITH SAWS1. Disconnect plug from power supplybefore changing blades, making cutting depth or cutting angle adjustments,

Page 2 - &. Decker

SAFETY RULES FOR POWER TOOLS1. KNOW YOUi POWER TOOL — Read owner’s manual carefully. Learn its applications and limitations as well

Related models: 97243 AL

Comments to this Manuals

No comments

Black-decker 3004 User Manual

Browse online or download User Manual for Power saws Black-decker 3004. Black & Decker 3004 User Manual

Summary of Contents

Related models: 97243 AL

Comments to this Manuals

Related products and manuals for Power saws Black-decker 3004