Black & Decker BDCMTOSS Instruction Manual download pdf (Page 7)

ENGLISH

(Original instructions)



INSTALLING/REMOVING SANDING ShEETS - fIGURE D

A diamond shaped platen uses a hook and loop adhesion system to

attach the sanding sheets. The platen allows you to use it on large flat

surfaces and tight spots or corners.

•Attachthesandingplatenasdescribedunder“Installing/Removing

Accessories.”

•Aligntheedgesonthesandingsheet,withtheedgeofthesanding

platen and press the sanding sheet onto the platen.

•Firmlypressthebasewiththesandingsheetattachedagainsta

flat surface and briefly switch the tool on. This provides for good

adhesion between the platen and the sanding sheet, and also helps

to prevent premature wear.

•Whenthetipofthesandingsheetbecomesworn,detachthesheetfrom

the platen, rotate and reapply.

hELPfUL hINTS

•Alwaysensuretheworkpieceisfirmlyheldorclampedtopreventmovement.Anymovementof

the material may affect the quality of the cutting or sanding finish.

•Donotstartsandingwithouthavingthesandpaperattachedtosandingplaten.

•Usecoarsegritpapertosandroughsurfaces,mediumgritforsmoothsurfacesandfinegritfor

the finishing surfaces. If necessary, first make a test run on scrap material.

•Excessiveforcewillreducetheworkingefficiencyandcausemotoroverload.Replacingthe

accessory regularly will maintain optimum working efficiency.

•Donotallowthesandpapertowearaway,itwilldamagethesandingplaten.

CCESSORIES

wARNING:

Theuseofanyaccessorynotrecommendedforusewiththistoolcouldbehazardous.

Recommendedaccessoriesforusewithyourtoolareavailablefromyourlocaldealerorauthorized

service center. If you need assistance regarding accessories, please call:

1-800-444-224

TROUBLEShOOTING

Problem Possible Cause Possible Solution

•Unitwillnotstart.  •Attachmentisnotsecured.  •Makecertaintheattachmentisfully

pushed into the Power Unit.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

IMPORTANT:ToassureproductSAFETYandRELIABILITY,repairs,maintenanceand

adjustment (other than those listed in this manual) should be performed by authorized service

centers or other qualified service personnel, always using identical replacement parts.

Technical data

Oscillating Tool

BDMTO-XE

No-load speed min

-1

Oscillating angle Degrees

2.8

Weight

when operate with 18V MATRIX unit

545

0-18500 (OPM)

Level of sound pressure according to EN 60745:

Sound pressure (L

) 86.5 dB(A), uncertainty (K) 3 dB(A)

Sound power (L

) 97.5 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Cutting wood (a

h, CW

) 5.0 m/s

, uncertainty (K) 1.5 m/s

Cutting metal (a

h, CM

) 8.0 m/s

, uncertainty (K) 1.5 m/s

Sanding (a

) 10.3 m/s

, uncertainty (K) 1.5 m/s

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Black & Decker BDCMTOSS Instruction Manual Page 7

Comments to this Manuals

Related products and manuals for Power tools Black & Decker BDCMTOSS