Black & Decker TM505 Instruction Manual download pdf (Page 12)

12 • ENGLISH

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power

tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts and

any other condition that may affect the power

tools operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

5. Service

a. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

6. Electrical safety

Your tool is double insulated; therefore no earth

wire is required. Always check that the main

voltage corresponds to the voltage on the rating

plate.

Warning! If the power cord is damaged, it must

be replaced by the manufacturer, authorized

Black & Decker Service Center or an equally

qualified person in order to avoid damage or

injury. If the power cord is replaced by an equally

qualified person, but not authorized by Black &

Decker, the warranty will not be valid.

7. Labels on tool

The label on your tool may include the following symbols:

FEATURES (Fig. A)

1. On/off switch

2. Lock-on button

3. Drilling mode selector

4. Chuck

ADDITIONAL SAFETY INSTRUCTIONS

FOR HAMMER DRILL

f Wear ear protectors with impact drills. Exposure to

noise can cause hearing loss.

f Hold power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will also make exposed metal

parts of the power tool “live” and shock the operator.

f Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body leaves

it unstable and may lead to loss of control.

f Before drilling into walls, floors or ceilings check for

the location of wiring and pipes.

f Avoid touching the tip of a drill bit just after drilling, as

it may be hot.

ASSEMBLY

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting a drill bit or screwdriver bit Keyed chuck

(fig. B)

f Open the chuck by turning the sleeve (5)

counterclockwise.

f Insert the bit shaft (6) into the chuck.

f Insert the chuck key (7) into each hole (8) in the side

of the chuck and turn clockwise until tight.

Removing and refitting the chuck (fig. C)

f Open the chuck as far as possible.

f Remove the chuck retaining screw, located in the

chuck, by turning it clockwise using a screwdriver.

f Tighten an Allen key into the chuck and strike it with

a hammer as shown.

f Remove the Allen key.

f Remove the chuck by turning it counterclockwise.

f To refit the chuck, screw it onto the spindle and secure

it with the chuck retaining screw.

USE

¡Warning! Let the tool work at its own pace. Do not

overload.

¡Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

1 2 ... 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Black & Decker TM505 Instruction Manual Page 12

Comments to this Manuals

Related products and manuals for Power tools Black & Decker TM505