Black & Decker DW248 User Manual download pdf (Page 21)

- Engaged level: if a stall condition still exists, the

electronics will stop the tool and the indicator will

light permanently.

- Alert mode: if the indicator flashes repeatedly, the

electronics do not function properly. Take your

tool to an authorized DEWALT repair agent.

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 50144;

therefore no earth wire is required.

Mains plug replacement

(U.K. & Ireland only)

• Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

DEWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

ENGLISH

en - 4 15

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or

For 115 V units with a power rating exceeding 1500 W,

we recommend to fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1.5 mm

. When using a cable reel, always

unwind the cable completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Inserting and removing a bit (fig. B)

• Open the chuck by turning the sleeve

counterclockwise and insert the bit shank.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 77 78

Comments to this Manuals

No comments

Black & Decker DW248 User Manual Page 21

Comments to this Manuals

Related products and manuals for Power drills Black & Decker DW248