Black & Decker RTX-B User Manual download pdf

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Double Insulated tools are equipped with a polarized plug (one blade is wider than

the other). This plug will fit in a polarized outlet only one way. If the plug does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug in any way. Double

Insulation eliminates the need for the three wire grounded power cord and grounded

power supply system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A"

or "W". These cords are rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica-

tion. A moment of inattention while operating power tools may result in serious personal

injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing , and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and bal-

ance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce the

risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced before

using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used on

another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

• Accessories must be rated for at least the speed recommended on the tool warning

label. Wheels and other accessories running over rated speed can fly apart and cause

injury.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating current

......................direct current

o........................no load speed

..........................

Class II Construction

........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations

per minute

ADDITIONAL SAFETY RULES F0R ROTARY TOOLS

ALWAYS WEAR EYE PROTECTION WHEN USING THIS TOOL!

• If accessory jams, turn tool off and disconnect from power supply before freeing

accessory from the jam.

• Hold tool by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

• When using cutoff wheels always have the work securely clamped. Never attempt to

hold the work with one hand while using any cutting accessory.

• Keep hands away from rotating accessories.

• Allow accessories and collets to cool before touching with bare hands. They will be

hot after using.

• Insure there are no foreign objects in the workpiece such as nails which if hit could

cause loss of control of unit.

• Always feed the cutter into the material in the same direction as the chips are being

thrown. Feeding the tool in the wrong direction can cause loss of control.

• Keep handles dry, clean, free from oil and grease. This will enable better control of the

tool.

• When cutting wood, extra care should be taken to avoid inhalation and minimize skin

contact.

• Wear ear protection. Noise level may be amplified when using tool in enclosed spaces.

• The RTX has an internal speed control, never use an external speed control on this

unit.

• Do not use worn accessories.

• Do not use grinding wheels that have cracks.

• When turning tool on, hold it away from your face, since a damaged accessory

could come apart.

1-800-54-HOW-TO

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

IF YOU SHOULD EXPERIENCE A PROBLEM

WITH YOUR BLACK & DECKER PURCHASE,

CALL 1-800-54-HOW-TO (1-800-544-6986).

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE

CAN RESOLVE YOUR PROBLEM OVER THE PHONE.

IF YOU HAVE A SUGGESTION OR COMMENT,

GIVE US A CALL. YOUR FEEDBACK IS VITAL

TO THE SUCCESS OF BLACK & DECKER'S QUALITY

IMPROVEMENT PROGRAM.

(544-6986)

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR ELPRODUCTO.

INSTRUCTION MANUAL

KEY INFORMATION YOU SHOULD KNOW:

• Do not tighten the collet nut without an accessory bit in place.

• Do not engage spindle lock until tool has come to a complete stop.

Collet nut

Écrou de la douille

Tuerca de la

mordaza

Collet

Douille

Mordaza

Spindle

Arbre

Flecha

Spindle Lock

Dispositif de verrouillage de l’arbre

Seguro de la flecha

On/Off Switch

Interrupteur

Interruptor de encendido y

apagado

On/Off Switch

Interrupteur

Interruptor de encendido y apagado

Driver Nut

Écrou de l'arbre

d'entraînement

Tuerca del mando

Flexible Shaft

Arbre flexible

Eje flexible

Driver Nut

Écrou de l'arbre

d'entraînement

Tuerca del mando

6 " (150mm)

150 mm 6 po

150 mm (6 pulg.)

Housing Cap

Couvercle du boîtier

Tapa de la carcaza

Catalog Number RTX

Tool Hanger

Douille de serrage

Pinza portapiezas

1 2 3 4 5

Summary of Contents

Page 1 - INSTRUCTION MANUAL

GENERAL SAFETY RULES WARNING:Read and understand all instructions. Failure to follow all instructions listedbelow may result in electric shock, fire a

Page 2 - 1 800 544-6986

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and otherconstruction activities contains chemicals known to cause cancer, bi

Page 3

électrique. Ne pas s'en servir lorsqu'on est fatigué ou affaibli par des drogues, del'alcool ou des médicaments. De graves blessures p

Page 4 - 326-7100

recommande d’utiliser un arbre ayant un rayon de 15,2 cm (6 po) ou plus. Un crochet desuspension (fig. 4) est fourni pour permettre d’immobiliser l’ou

Page 5

haga ese tipo de trabajo. Para reducir la exposición a eas sustancias químicas: trabaje enespacios bien ventilados y hágalo con equipos de seguridad a

Comments to this Manuals

No comments

Black & Decker RTX-B User Manual

Browse online or download User Manual for Power routers Black & Decker RTX-B. Black & Decker RTX-B User's Manual

Summary of Contents

Comments to this Manuals