Black & Decker KA161 Instruction Manual download pdf (Page 8)

ENGLISH

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. On/off switch

2. Dust extraction connector

3. Base

4. Tip holder

5. Sanding base tip

6. Finger attachment

7. Prole attachment

8. Screw

9. Sanding proles

In addition, this tool is supplied with some or all of the

following accessories:

Accessory Recommended application

and use

u Coarse grit sandpaper Fast paint, varnish and rust

removal

u Medium grit sandpaper Paint, varnish and rust removal

u Fine grit sandpaper Surface blending and nishing

u Extra ne grit sandpaper Sanding between coats

u Detail sanding tips Corners and hard to reach places

u 1 OT polishing/stripping Polishing metals, stripping

wool varnish and glass cleaning

u Grey foam pad Applying and removing polish

u Red non-woven pad Heavy scrubbing and rust

removal

u Grey abrasive paper Polishing plastics

u Contour attachments Curves and proles

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fittingsandingsheets(g.A&B)

u Detach the two diamond-shaped tips (10) from the

sanding sheet (11).

u Hold the tool with the sanding base facing upwards.

u Place the sanding sheet (11) onto the sanding base,

making sure that the holes in the sheet line up with the

holes in the base.

The diamond-shaped tip (10) can be reversed and replaced

when worn.

u When the front part of the tip is worn, detach it from the

sheet, reverse it and press it onto the sanding base again.

u When the whole tip is worn, remove it from the sanding

base and t a new tip.

u The polishing foam and pads (14) can be tted the same

way as the sanding sheets.

Tipofthesandingbase(g.C)

When the sanding base tip (5) or tip holder (4) is worn, it can

be reversed or replaced. Spare parts are available from your

Black & Decker dealer.

u Remove the screw (8).

u Reverse or replace the worn part.

u Fit and tighten the screw.

Fingerattachment(g.D)

The nger attachment is used for ne detail sanding.

u Remove the screw (8).

u Remove the diamond-shaped tip holder (4) from the

sanding base.

u Fit the nger attachment (6) onto the sanding base.

u Fit and tighten the screw.

u Fit the appropiate sanding sheet (12) onto the nger

attachment.

Proleattachment(KA160K/KA161Konly)(g.E)

The prole attachment is used for contour sanding.

u Remove the screw (8).

u Remove the diamond-shaped tip holder (4) from the

sanding base.

u Fit the prole attachment (7) onto the sanding base.

u Fit and tighten the screw.

Fittingandremovingasandingprole(g.F1&F2)

u Choose the sanding prole most suitable for your application.

u Place one end of the sanding prole (9) into the recess at

the front end of the prole holder (7).

u Push the other end of the sanding prole until it clicks into

place.

u To remove the sanding prole, push it forward and pull the

rear end out of the prole holder (g. F2).

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 75 76

Comments to this Manuals

No comments

Black & Decker KA161 Instruction Manual Page 8

Comments to this Manuals

Related products and manuals for Power tools Black & Decker KA161