Black-decker 722066 User Manual download pdf

B/ack&Deckep, jigsaw.

SAFETY RULES

FOR POWER TOOLS

1. KNOW mm POWEi tool ^ Read owner's manual care»

fully. Learn its applications and limitations as well as the

specific potential hazards peculiar to this tool.

2. KEEP GOAIDS IN PLACE and in working order.

3. KEEP WORK AREA CLEAN. Cluttered areas and benches

invite accidents.

4. A¥OID DANGEIO'US ENfllONMENT. Don't use power tool

in damp or wet locations. And keep work area well lit.

5. KEEP CHILDREN AWAY. All visitors should be kept safe

distance from work area.

6. STORE IDLE TOOLS. When not in use, tools should be

stored in dry, high or locked-up place — out of reach of

children.

7. DON'T FORCE TOOL. It will do the job better and safer at

the rate for which it was designed.

8. USE RIGHT TOOL. Don't force small tool or attachment to

do the Job of a heavy duty tool.

9. WEAR PROPER APPAREL. No loose clothing or Jewelry to

get caught in moving parts. Rubber gloves and footwear

are recommended when working outdoors.

10. USE SAFETY GLASSES with most tools. Also face or dust

mask if cutting operation is dusty.

11. DON'T ABUSE CORD. Never carry tool by cord or yank It

to disconnect from receptacle. Keep cord from heat, oil

and sharp edges.

12. SECURE WORK. Use clamps or a vise to hold work. It's

safer than using your hand and it frees both hands to

operate tool.

13. DON'T 0¥E11EACH. Keep proper footing and balance at

all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp at all

times, and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS. When not in use, before servicing;

when changing accessories such as blades, bits, cutters,

etc.

16.

17.

REMO¥E ADJUSTING KEYS AND WRENCHES. Form habit

of checking to see that keys and adjusting wrenches are

removed from tool before turning it on.

A¥OID ACCIDENTAL STARTING: Don't carry plugged-in

tool with finger on switch.

WHEN SAWING, never reach under or behind the material being

cut for any reason.

MOTOR

Your Black and Decker tool is powered by a B&D-built motor.

Be sure your power supply agrees with nameplate marking.

120 ¥olts 50/60 Hz means Alternating Current (normal 120

volt, 60 cycle house current). Voltage variation of more than

10% will cause loss of power and over-heating. All B&D tools

are factory-tested; if this tool does not operate, check the

supply line for blown fuses; plug and receptacle for contact.

DOUBLE-INSULATION

Your tool is DOUBLE-INSULATED to give you added safety.

This means that it is constructed throughout with TWO separate

“layers" of electrical insulation or one DOUBLE thickness of

insulation between you and the tool's electrical system.

Tools built with this improved insulation system are not in

tended to be grounded. As a result, your tool is equipped with

a two-prong plug which permits you to use any conventional

120 volt electrical outlet without concern for maintaining a

ground connection.

NOTE: DOUBLE-INSULATION does not take the place of norma!

safety precautions when operating this tool. The improved

insulation system is for added protection against injury result

ing from a possible electrical insulation failure within the tool.

CAUTION: When servicing Double-Insulated Tools, it is extremely

important that ONLY IDENTICAL REPLACEMENT PARTS BE

USED.

EXTENSION CORD

When using the tool at a considerable distance from the power

source, an extension cord of adequate size must be used for

safety, and to prevent loss of power and over-heating. Use the

table below to determine m.inimum wire size required.

Before using cords, inspect them for loose or exposed wires

and damaged insulation. Make any needed repairs or replace

ment before using your power tool.

Extension Cord Length

Minimum | 120 Volt Tools

Wire Size-

220 Volt Tools

* American Wire Gauge

Up to

100 Ft.

150 Ft.

75 Ft.

to 125 Ft. to 200 Ft.

LUBRICATION

After every 15 hours of actual running time, place 2 drops of

machine oil in the oil hole located in the side of the tool near

the front. It is recommended that, at least once a year, you

take or send the tool to a B&D Service Center for a thorough

cleaning, inspection and lubrication of the gear case.

ATTACHING BLADES

Disconnect tool from extension cord or wall receptacle. Loosen

screw at side of chuck with screwdriver. Insert blade in chuck

as far as it will go (about Tighten screw until it is firm

against blade.

Your B&D Dealer carries a wide selection of Jig Saw Blades

for cutting many kinds of materials. These include wood, metal,

plastics, fiberglass, formica, asbestos, slate, etc.

1 2

Summary of Contents

Page 1 - B/ack&Deckep, jigsaw

+B/ack&Deckep, jigsaw.SAFETY RULES FOR POWER TOOLS1. KNOW mm POWEi tool ^ Read owner's manual care» fully. Learn its applications

Page 2 - Bbok a Decker, jig saw

Bbok a Decker, jig saw.SWITCHMETAL CUTTINGFIGUiE 1FIGURE 2FIGURESPush the Switch Button forward to turn the saw “ON”. As you push the but

Related models: 6700

Comments to this Manuals

No comments

Black-decker 722066 User Manual

Browse online or download User Manual for Power saws Black-decker 722066. Black & Decker 722066 User Manual

Summary of Contents

Related models: 6700

Comments to this Manuals

Related products and manuals for Power saws Black-decker 722066