VEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.ADVERTENCI
10This warranty does not apply to accessories. This warranty gives you specific legal rightsand you may have other rights which vary from state to sta
11SSSScccciiiieeee ééééggggooooïïïïnnnneeee éééélllleeeeccccttttrrrriiiiqqqquuuueeee ssssaaaannnnssss ffffiiiillllMODE D’EMPLOICONSERVEZ C
12IMPORTANTES MESURES DE SÉCURITÉ - POUR TOUS LESOUTILS ALIMENTÉS PAR PILESAVERTISSEMENT! LIRE ET COMPRENDRE TOUTES LES DIRECTIVES. Le non-respect de
• Lorsque la pile ne sert pas, l’éloigner de tout objet métallique (comme destrombones, des pièces de monnaie, des clés, des clous, des vis ou tout au
14• Éviter tout contact prolongé avec la poussière soulevée par cet outil ou autresoutils électriques. Porter des vêtements de protection et nettoyer
1512. Une petite fuite de liquide peut se produire dans les cellules de pile en casd’utilisation extrême, de charge ou de conditions de température. C
16DESCRIPTIONFONCTIONNELLE - figure A1. Détente2. Bouton de verrouillage3. Prise femelle4. Semelle5. Levier de dégagement de la bride de lame6. Charge
11517GFH90504595 02 CHS6000 Hand SAW 8/16/06 11:11 AM Page 1790511381
18ASSEMBLAGEINSTALLATION DU SUPPORT MURAL Utiliser le matériel fourni uniquement si l’appareil sera accroché sur un mur creuxconventionnel comme une c
19provoquer une perte de maîtrise de l’outil.• Positionner la semelle fermement contre la pièce à couper.• Mettre en marche le moteur de la scie avant
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATEDTOOLSWARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.Failure to follow all instructions listed below, may
décharge complète des piles. Au moyen d’un tournevis, enlever les vis du boîtier duproduit, puis soulever à moitié le boîtier de l’outil. Débrancher l
21Information sur les réparationsTous les centres de réparation Black & Decker sont dotés de personnel qualifié enmatière d’outillage électrique;
22SSSSiiiieeeerrrrrrrraaaa mmmmeeeeccccáááánnnniiiiccccaaaa ddddeeee mmmmaaaannnnooooiiiinnnnaaaalllláááámmmmbbbbrrrriiiiccccaaaaMANUAL DEINS
23REGLAS GENERALES DE SEGURIDAD - PARA TODAS LASHERRAMIENTAS OPERADAS CON BATERÍAS¡ADVERTENCIA! LEA Y COMPRENDA TODAS LAS INSTRUCCIONES. No hacerlopue
24herramienta se encienda accidentalmente.• Guarde las herramientas fuera del alcance de los niños y de otras personas nocapacitadas. Las herramientas
25como las máscaras para polvo especialmente diseñadas para filtrar las partículasmicroscópicas.• Evite el contacto prolongado con las partículas de p
269. Utilice un solo cargador cuando carga.10. No intente abrir el cargador. No contiene elementos que el cliente pueda reparar.Devuelva a cualquier c
27DESCRIPCIÓN DE LASFUNCIONES - Figura A1. Interruptor de encendido/apagado2. Botón de bloqueo3. Enchufe de carga4. Zapata5. Palanca de liberación de
28115GFH90504595 02 CHS6000 Hand SAW 8/16/06 11:11 AM Page 2890511381
29MONTAJECÓMO COLGAR EL SOPORTE DE MONTAJE EN PARED Utilice el equipo provisto sólo si desea colgar el aparato en una construcción de paredhueca conve
3• When battery pack is not in use, keep it away from other metal objects like: paperclips, coins, keys, nails, screws or other small metal objects th
30CORTES EN MADERA • Antes de cortar cualquier tipo de madera, utilice abrazaderas u otra forma práctica paraasegurar y sostener la pieza de trabajo
31IMPORTANTE: Para asegurar la SEGURIDAD y la CONFIABILIDAD del producto, lasreparaciones, el mantenimiento y los ajustes se deben realizar en los cen
32DETECCIÓN DE PROBLEMASProblema Causa posible Solución posible• La unidad no enciende. • La batería no carga. • Verifique los requisitos de carga de
33BLACK & DECKER S.A. DE C.V.BOSQUES DE CIDROS ACCESO RADIATAS NO. 42COL. BOSQUES DE LAS LOMAS.05120 MÉXICO, D.FTEL. 55-5326-7100SECCI NAMARIL
3490504595 02 CHS6000 Hand SAW 8/16/06 11:11 AM Page 3490511381
The label on your tool may include the following symbols.V ...volts A...amperesHz ...
5(1.) Plugging the charger output plug (10) directly into the charging socket (3) of the sawas shown in figure B or, (2) Plugging the charger output
6B CD E1110375FG1090504595 02 CHS6000 Hand SAW 8/16/06 11:11 AM Page 690511381
7ASSEMBLYHANGING THE WALL MOUNTING BRACKET Use the hardware provided only if hanging on conventional hollow wall construction suchas sheet rock or pla
8• Release the blade clamp release lever. To remove blade from saw:• Push down on the blade clamp release lever to its full open position.• Remove bl
9stops to ensure a complete discharge of the batteries. Using a screwdriver, remove thescrews in the product housing and lift the housing half from th
Comments to this Manuals